Ge Timer Switch 532641l3 Instruction Manual Pdf Pdf Install 〈Desktop HIGH-QUALITY〉
If GE’s site redirects you (common for discontinued models), go to:
| Parameter | Rating | |-----------|--------| | Voltage | 120–277 VAC, 60 Hz | | Resistive load | 40 A (240 VAC) | | Tungsten / Ballast | 10 A @ 120 VAC | | Motor (HP) | 2 HP @ 120/240 VAC | | Timer mechanism | Synchronous motor (24-hour dial) | | Minimum ON/OFF time | 30 minutes (using two trippers) |
The GE 532641L3 is a single-pole, 24-hour mechanical timer switch rated for 40A resistive, 30A inductive, or 5A tungsten. It’s designed for 120V to 277V AC systems. Unlike digital timers, this model uses a motor-driven dial to physically open and close a switch at preset times.
Without the GE timer switch 532641L3 instruction manual PDF, you risk:
The official manual contains critical torque specs for terminal screws (12-14 in-lbs), wire gauge recommendations (14 AWG to 8 AWG), and temperature ratings (-20°F to 120°F).
Your GE timer has four color-coded leads (or screw terminals): | Timer Wire | Connect To | Notes | |------------|------------|-------| | Black (Line) | House black wire (incoming hot) | Use a wire nut | | Red (Load) | House black wire going to light | Often marked “Load” | | White (Neutral) | House white neutral bundle | Critical for timer electronics | | Green (Ground) | House bare copper or green ground | |
Important: Do not confuse the timer’s black and red. Swapping line & load may damage the timer or cause lights to stay on constantly.
The GE in-wall digital timer (often part of the SunSmart line) is designed for automating indoor or outdoor lighting. Follow these steps for a safe and successful installation and setup. 🛠️ Installation Guide ge timer switch 532641l3 instruction manual pdf pdf install
Caution: Always turn off power at the circuit breaker before beginning any electrical work.
Remove Old Switch: Take off the wall plate and unscrew the existing switch. Identify your wires. Identify Wiring:
Line (Hot): Typically black, carrying power from the source. Load: Carries power to the light fixture.
Neutral: Usually a bundle of white wires in the back of the box (Required for this timer). Ground: Bare copper or green wire. Connect the Timer: Line: Connect the "Hot" wire to the LINE terminal.
Load: Connect the wire going to the light to the LOAD terminal.
Neutral: Use the provided jumper wire to connect the timer’s NEUTRAL terminal to the white neutral bundle. Ground: Connect to the GROUND terminal.
Secure and Power Up: Push wires into the box, mount the timer with screws, and replace the wall plate. Turn the breaker back on. 🕒 Programming Instructions If GE’s site redirects you (common for discontinued
If the screen is blank after restoring power, let it charge for 15–30 minutes before programming. 1. Initial Reset
Use a toothpick or paperclip to press the small Reset (R) button to clear old settings. 2. Set Current Time Press and hold the CLOCK button.
While holding CLOCK, press HOUR and MIN to set the time (check for AM/PM).
While holding CLOCK, press DAY to select the current day of the week. 3. Program On/Off Times Press PROGRAM to see "1 ON".
Use HOUR and MIN to set the first "On" time. Use DAY to select specific days or "Daily".
Press PROGRAM again to see "1 OFF" and repeat the process for the "Off" time. Press CLOCK to save and exit. 4. Select Mode Digital Timer Setup Instructions | PDF - Scribd
The GE timer switch model (also referenced as ) is a dusk-to-dawn digital programmable in-wall timer. It is designed to automate indoor or outdoor lighting by using either fixed time schedules or integrated photocell sensors for ambient light detection. JustAnswer Installation Instructions The official manual contains critical torque specs for
Shut off power at the circuit breaker or fuse box before beginning installation. m.media-amazon.com Prepare Wires
: Remove the existing wall switch and strip the building wires to approximately 3/8 inch. Identify Connections Black Wire : Connect to the Line (Hot) wire from the power source. : Connect to the wire (the wire going to the light/appliance). White Wire : Connect to the
wire. Note that this timer requires a neutral wire to function. Green/Bare Wire : Connect to the terminal or wire in the junction box. Secure Unit
: Carefully tuck wires into the wall box and secure the timer using the provided screws. Install the wall plate. Restore Power
: Turn the power back on at the breaker. The unit may take about 1 minute to charge its internal backup battery before the display functions. Programming Guide
To set up the timer for the first time, use a small, non-metallic tool (like a toothpick) to press the
HET01 Smart Timer Installation Guide | PDF | Electrician - Scribd
