Yp-05 Schematic [ Full HD ]

Yp-05 Schematic [ Full HD ]

The power stage is designed to accept an input voltage range of [e.g., 9V–24V] via a [connector type, e.g., barrel jack]. The schematic utilizes a [Insert Regulator Type, e.g., LM7805 or Buck Converter] to step this down to a steady 5V/3.3V rail for the logic components.

| Reference | Typical Value | Function | Failure Indicator | | :--- | :--- | :--- | :--- | | F1 | 2A – 5A 250V | Protection | Open circuit (no continuity) | | RT1 | 5D-11 | Inrush limit | Cracked, high resistance (>50Ω) | | C1 | 100µF/400V | Bulk storage | Bulging top, low capacitance | | Rstart | 150k-300k | Startup | Open circuit (no P_IC VCC) | | Q1 | 600V N-MOSFET | Switching | Shorted G-D-S | | U1 | UC3844 | PWM control | No oscillation on pin 6 (Gate) | | U2 | PC817 | Feedback | Low CTR (output can’t pull low) | | D5, D6 | UF4007 | Rectification | Shorted or open | | U4 | 7815/7824 | Linear reg | Input voltage present, output zero |

If the Yp-05 fails to operate, the schematic suggests checking the following test points:

The Yp-05 is not just for stock use. Here are three advanced modifications that engineers love. Yp-05 Schematic

The central IC is almost always a XL4015, LM2596, or a pin-compatible alternative like the TPS5430 (for synchronous versions). Let’s assume the classic XL4015 topology:

| Pin# | Name | Function | |------|------|----------| | 1 | FB (Feedback) | Connects to voltage divider (R1,R2) to set Vout = 1.25V * (1+R2/R1) | | 2 | GND | Ground | | 3 | SW (Switch) | Connects to inductor (L1) and Schottky catch diode (D2) | | 4 | VIN | Input voltage (bypassed by C1) | | 5 | EN (Enable) | Pull high to enable; low = shutdown |

The Yp-05 schematic shows a classic buck converter: The internal MOSFET switches at ~150kHz, dumping energy into L1 (33µH – 47µH). During the off-time, current flows through D2 (SS54). The output capacitor C3 (220µF) filters the result. The power stage is designed to accept an

Use isolated differential probe or DMM with CAT II rating. Do not touch primary side.

| Test Point | Expected Voltage (No Load) | Waveform | | :--- | :--- | :--- | | Across C1 (primary) | 310-340V DC (if 230V AC input) | Smooth DC | | U1 Pin 7 (VCC) | 12V – 18V DC (stable) | DC | | U1 Pin 6 (Output) | 0.5V – 5V pulse | Square wave, 50-100kHz | | Secondary main DC | 18V – 30V (before regulator) | Sawtooth + DC | | U4 Output | 15.0V ± 5% | Clean DC | | U5 Output | -15.0V ± 5% | Clean DC |

The designation "YP-05" typically refers to a small form-factor, dual-voltage power supply or driver interface board. It is not a standardized global IC but rather a PCB assembly identifier used by various manufacturers (e.g., Yaskawa clones, Chinese VFD suppliers, or generic industrial controls). The Yp-05 is not just for stock use

Common characteristics:

If you have a physical board: Look for the revision number (e.g., YP-05 V2.0). This guide assumes a typical switching regulator topology.

Document Title: Yp-05 Circuit Schematic – Functional Overview Subject: Yp-05 Schematic Date: October 26, 2023

The power stage is designed to accept an input voltage range of [e.g., 9V–24V] via a [connector type, e.g., barrel jack]. The schematic utilizes a [Insert Regulator Type, e.g., LM7805 or Buck Converter] to step this down to a steady 5V/3.3V rail for the logic components.

| Reference | Typical Value | Function | Failure Indicator | | :--- | :--- | :--- | :--- | | F1 | 2A – 5A 250V | Protection | Open circuit (no continuity) | | RT1 | 5D-11 | Inrush limit | Cracked, high resistance (>50Ω) | | C1 | 100µF/400V | Bulk storage | Bulging top, low capacitance | | Rstart | 150k-300k | Startup | Open circuit (no P_IC VCC) | | Q1 | 600V N-MOSFET | Switching | Shorted G-D-S | | U1 | UC3844 | PWM control | No oscillation on pin 6 (Gate) | | U2 | PC817 | Feedback | Low CTR (output can’t pull low) | | D5, D6 | UF4007 | Rectification | Shorted or open | | U4 | 7815/7824 | Linear reg | Input voltage present, output zero |

If the Yp-05 fails to operate, the schematic suggests checking the following test points:

The Yp-05 is not just for stock use. Here are three advanced modifications that engineers love.

The central IC is almost always a XL4015, LM2596, or a pin-compatible alternative like the TPS5430 (for synchronous versions). Let’s assume the classic XL4015 topology:

| Pin# | Name | Function | |------|------|----------| | 1 | FB (Feedback) | Connects to voltage divider (R1,R2) to set Vout = 1.25V * (1+R2/R1) | | 2 | GND | Ground | | 3 | SW (Switch) | Connects to inductor (L1) and Schottky catch diode (D2) | | 4 | VIN | Input voltage (bypassed by C1) | | 5 | EN (Enable) | Pull high to enable; low = shutdown |

The Yp-05 schematic shows a classic buck converter: The internal MOSFET switches at ~150kHz, dumping energy into L1 (33µH – 47µH). During the off-time, current flows through D2 (SS54). The output capacitor C3 (220µF) filters the result.

Use isolated differential probe or DMM with CAT II rating. Do not touch primary side.

| Test Point | Expected Voltage (No Load) | Waveform | | :--- | :--- | :--- | | Across C1 (primary) | 310-340V DC (if 230V AC input) | Smooth DC | | U1 Pin 7 (VCC) | 12V – 18V DC (stable) | DC | | U1 Pin 6 (Output) | 0.5V – 5V pulse | Square wave, 50-100kHz | | Secondary main DC | 18V – 30V (before regulator) | Sawtooth + DC | | U4 Output | 15.0V ± 5% | Clean DC | | U5 Output | -15.0V ± 5% | Clean DC |

The designation "YP-05" typically refers to a small form-factor, dual-voltage power supply or driver interface board. It is not a standardized global IC but rather a PCB assembly identifier used by various manufacturers (e.g., Yaskawa clones, Chinese VFD suppliers, or generic industrial controls).

Common characteristics:

If you have a physical board: Look for the revision number (e.g., YP-05 V2.0). This guide assumes a typical switching regulator topology.

Document Title: Yp-05 Circuit Schematic – Functional Overview Subject: Yp-05 Schematic Date: October 26, 2023

Importante: Este site faz uso de cookies que podem conter informações de rastreamento sobre os visitantes.