Sc67310 Ricoh Error Free -

The fusing web is a consumable fabric roll that lubricates the fusing roller to prevent toner offset. If the web roll is depleted, a sensor triggers an end-of-life signal.

Last Updated: October 2024
Target Models: Ricoh MP series, IM series, and other production printers

If you manage a Ricoh multifunction printer (MFP) in a busy office or print shop, encountering a sudden error code can bring productivity to a screeching halt. One of the most confusing and persistent errors users face is the SC67310 Ricoh error.

This article is your ultimate resource. We will not only explain what the SC67310 error means but also provide a step-by-step roadmap to make your Ricoh device SC67310 error free. By the end of this guide, you will understand the root causes, the repair process, and long-term prevention strategies.

This is the most common fix for SC67310.

Warning: Only perform this if you are a certified technician or comfortable with hardware handling. Static discharge can damage components.

The Ricoh SC673-10 error code is a communication error that typically occurs between the controller board and the operation panel or other engine components. In many Ricoh models, including the MP and IMC series, this code indicates that the controller failed to receive a response from a peripheral or internal board within a specified timeframe. Common Causes of SC673-10

The primary cause of this error is a communication breakdown within the machine's hardware. Specific triggers often include:

Failed Controller Board: The main controller board is unable to process or send signals.

Poor Cable Connections: Loose or damaged flat-ribbon cables between the controller and the operation panel.

Firmware Mismatch: A recent update may have caused an incompatibility between the engine and controller software.

Faulty Optional RAM: If your machine has optional memory installed, a defect in the RAM module can disrupt the startup sequence. How to Resolve the Error 1. Basic Power Reset

Before attempting technical repairs, try a standard power cycle to clear temporary glitches.

Turn off the copier using the power button on the control panel. Unplug the power cord from the wall outlet. sc67310 ricoh error free

Wait at least 30 to 60 seconds to allow all capacitors to discharge. Plug the machine back in and restart it. 2. Entering Service Mode to Reset the SC Code

If the error persists after a power cycle, you may need to clear the "Service Call" (SC) status manually. On the keypad, press Reset (Clear Modes). Type 1 0 7.

Press and hold the Stop (Clear) button until the Service Mode menu appears. Select System SP. Navigate to SP-5810 (SC Reset) and select "Execute".

Power the machine off and then on again using the main power switch. 3. Hardware Maintenance

If the reset does not fix the issue, physical components likely need inspection:

Reseat Connections: Open the controller cover and ensure all cables, especially those connected to the BICU board and operation panel, are firmly seated.

Check the RAM: If the error occurs during the boot-up sequence, try removing and re-installing any optional RAM modules.

Inspect the Hard Drive: In some cases, a failing hard disk drive (HDD) can cause communication timeouts. You can attempt to format the HDD via SP-5832 or temporarily disconnect it to see if the error clears. Preventing Future Communication Errors

To keep your Ricoh machine "error-free," consider these maintenance tips:

To become SC67310 Ricoh error free, you must understand the potential triggers:

The following actions were taken to clear the error:

To prevent the recurrence of SC67310:

Report Prepared By: Service Technician

It sounds like you’re looking for a confirmation text or message indicating that the Ricoh SC-673-10 error has been resolved.

Here’s a clean, professional text you can use (e.g., in a log, email, or service report):

"SC673-10 Ricoh error cleared. Device communication恢复正常. No further action required."

Or, more simply:

"Ricoh SC673-10 error resolved – system error‑free."

If you need a plain status line:

Status: SC673-10 resolved. Machine error‑free.

The error code SC673-10 (often part of the broader SC673 series) on Ricoh devices typically indicates a communication error between the operation panel and the controller board, or a failure during the system's startup sequence. Understanding the Error

When your Ricoh machine displays this code, it means the controller board has timed out or failed to receive a response from the communication interface within the allotted time after powering on. This can be caused by:

Controller Board Stalling: The main processing board is hanging during boot-up.

Poor Connections: Loose cables between the operation panel and the controller.

Firmware Mismatch: Conflict between the engine and controller software.

Defective Hardware: Faulty RAM, HDD, or the Controller board itself. Troubleshooting Steps The fusing web is a consumable fabric roll

To resolve this and return to "error-free" status, follow these steps in order:

Ricoh error code SC673-10 typically indicates a communication timeout between the controller and the operation panel during startup. This is often caused by a loose connection, a software hang-up, or a faulty control panel board. Common Troubleshooting Steps Hard Power Cycle: Turn off the main power switch.

Unplug the power cord from the wall outlet and wait for at least 60 seconds.

Plug it back in (directly to a wall outlet if possible) and restart the machine. Check Physical Connections:

Ensure the cables connecting the operation panel to the main controller are securely plugged in and not pinched or damaged. Enter Service Mode to Reset:

If the error persists, you may need to clear it via Service Program (SP) mode.

Press the Reset/Clear Modes button, then enter 1-0-7, and hold the Stop/Clear button until the SP menu appears.

Navigate to System SP > SP 5-810 (SC Reset) and select Execute.

Turn the main power off and then back on to finalize the reset. Technical Causes

Controller Software: A firmware mismatch or a software hang-up can prevent the panel from communicating.

Hardware Failure: If resetting does not work, the Operation Panel board or the Controller board may require professional replacement.

For detailed manual instructions or replacement parts, you can check the Ricoh Support Portal or look for specific model guides on Scribd.