Cobra 3195 Alarm Manual Full ✦ [ UPDATED ]

Fix: The internal backup battery (in the siren unit) is dead. Replace the entire siren unit (Cobra part #CSF-1) or disconnect silent mode. Check fuse #2 (5A) in the main harness.

The Cobra 3195 alarm system displays error codes to indicate system problems. Common error codes include:

Maintenance and Testing

Regular maintenance and testing are essential to ensure the Cobra 3195 alarm system operates correctly.

Conclusion

The Cobra 3195 alarm system is a reliable and efficient security solution for residential and commercial properties. This report provides a comprehensive guide to the system's features, installation, operation, and troubleshooting. Regular maintenance and testing are essential to ensure the system operates correctly and provides optimal security.

Recommendations

Limitations and Future Development

The Cobra 3195 alarm system has limitations, including:

Future development could include:

This report provides a comprehensive guide to the Cobra 3195 alarm manual. However, it is essential to consult the manufacturer's documentation and seek professional assistance for specific installation, operation, and troubleshooting requirements.

The manual for the Cobra 3195 alarm (part of the 3100 series from Vodafone Automotive) details procedures for arming, disarming, and emergency overrides. This system is a Thatcham-approved modular alarm typically controlled by the vehicle's original remote or a Cobra-specific key fob. Core Operations Arming/Disarming

: Generally synchronized with your vehicle’s central locking. If using a Cobra remote, press the large button to arm (confirmed by two beeps and flashes) and the same button to disarm (one beep and flash). Emergency Override

: If your remote fails, you can disarm the system using a unique Personal Identification Number (PIN) found on the "Cobra PIN Card" provided at installation. Turn the ignition cobra 3195 alarm manual full

3 times within 7 seconds. The status LED will illuminate for 3 seconds. Immediately after the LED goes out, turn the ignition

Count the LED flashes for the first digit of your PIN. Turn the ignition once the count is reached, then back Repeat for the remaining three digits. Key Functions & Indicators LED Status Rapid Flashing

: The system is in the "pre-arm" phase (approx. 20–30 seconds). Slow Flashing : System is fully armed. Diagnostic Flashes

: If the alarm triggered while you were away, the LED will flash in a specific sequence (e.g., 5 flashes for a boot/bonnet circuit issue) when you disarm it. Volumetric Protection

: To arm the alarm while leaving a pet or person inside (disabling internal motion sensors), press the remote button twice within 3 seconds when arming. Programming & Manuals New Remotes

: Programming usually requires entering the PIN first to put the system into "learning mode." Once in mode, you press both buttons on the remote for 10 seconds until the remote's LED stops flashing and stays on. Digital Copies

: You can find full PDF documentation for similar 3100-series models (like the 3198) on or the official Vodafone Automotive Manuals Portal Do you need the specific wiring diagram for installation or the programming code sequence for a new key fob?

In this section you will find our manuals - Vodafone Automotive

The Cobra 3195 is part of the legacy 3000 series (similar to the 3193 and 3198 models), which are standard vehicle security systems featuring radio remote control, engine immobilization, and volumetric protection. Core Operation Guide

Arming: Press the large button (A) on the remote key fob. The direction lights will flash twice to confirm the system is armed.

Disarming: Press the small button (B). The direction lights will flash once, and the status LED will turn off.

Emergency Override: If the remote fails, you must use the unique 4-digit PIN code provided on the system's security card. Programming New Remote Fobs

To add a new transmitter (up to 4 per system), follow these sequential steps: Remote Trunk Release (If installed):

Prepare Remotes: Press both buttons on the remote simultaneously until the LED stops flashing (approx. 10 seconds). The LED will then stay illuminated. Repeat for all remotes you intend to use.

Initialize Mode: Turn the ignition ON and OFF 3 times within 7 seconds. The dashboard security LED will light for 3 seconds. Enter PIN: Immediately after the LED goes out, turn the ignition ON.

Count the LED flashes until they reach your first PIN digit, then turn the ignition OFF.

Turn ignition ON again and repeat for the remaining three digits.

Sync: If the code is correct, the LED remains lit. Press the large button on each remote until the dashboard LED goes out and comes back on to confirm sync. Exit: Turn the ignition OFF and test each fob. Common Troubleshooting

Battery Low: If the remote's LED flashes weakly or the system beeps upon disarming, replace the remote battery.

Trigger History: If the alarm went off while you were away, the status LED will blink in a specific pattern when you disarm: 1 blink: Door or boot opened. 3 blinks: Bonnet opened. 4 blinks: Ignition/hotwire attempt. 5 blinks: Volumetric/motion sensor triggered. Coding new Cobra remote. - Technical Talk

The Cobra 3195 is a legacy vehicle security system known for its reliable perimeter and volumetric protection. While specific 3195 manuals are often hosted as legacy PDFs on sites like Scribd (similar to the 3198 model), its operation follows standard Cobra logic. Core Operations

Arming: Press the large button (Button A) on the remote. Arming is confirmed by the vehicle doors locking, flashes of the direction lights, and a solid LED on the emergency panel.

Disarming: Press the small button (Button B). This unlocks the doors and turns the dashboard LED off.

Volumetric Exclusion: To arm the system while leaving windows slightly open or a pet inside, arm the system normally and then press Button B twice within 20 seconds to disable the internal motion sensors for that cycle. Programming & Resynchronization

If your remote stops working, you may need to resynchronize it or add a new one: Coding new Cobra remote. - Technical Talk

The Cobra 3195 is a legacy vehicle security system often installed in cars like the Lotus Elise and Exige. Since this model is part of Cobra's older "Bridge" or "8000" series, it shares core operational procedures with models like the 3198 and 8185. 1. System Operation on the remote key fob. Indicators: Fix: The internal backup battery (in the siren

Turn indicators blink twice; the status LED begins to flash. Disarming: Indicators: Turn indicators blink once; the status LED goes out. Ultrasonic Sensor Exclusion: If you need to leave a pet or person inside, press

within 20 seconds of arming to disable interior motion sensors for that cycle. Midlands Lotus Owners Club 2. Emergency PIN Override

If your remote is lost or the battery is dead, you can disarm the system using your unique 4-digit PIN: Midlands Lotus Owners Club Turn the ignition ON and OFF 3 times within 5 seconds.

The security LED will blink once to signal it is ready for the PIN. Enter the 1st digit: Turn the ignition

, count the number of LED blinks equal to the first digit, then turn the ignition Repeat Step 3 for the remaining three digits. If correct, the alarm will disarm. Midlands Lotus Owners Club 3. Remote Key Fob Programming To sync a new or existing remote: Midlands Lotus Owners Club Prepare remotes:

Hold both buttons on the remote until the fob LED stops flashing (approx. 10 seconds). The LED will then stay lit. Enter Program Mode: Perform the ignition ON/OFF 3 times sequence (same as PIN entry) and enter your 4-digit PIN. Once the PIN is accepted and the ignition is , the security LED will stay lit. Press the large

on each remote. The security LED will blink once to confirm each one. Turn off the ignition to exit. Midlands Lotus Owners Club 4. Troubleshooting LED Flash Codes

After an alarm trigger, the dashboard LED will flash a specific pattern to indicate the cause:

How to Read Vodafone Automotive & Cobra Car Alarm Fault Codes

| Button | Function | Typical Use | |--------|----------|-------------| | MENU | Access configuration screens | Changing settings, adding users, etc. | | ▲ / ▼ | Navigate up‑down or increase/decrease values | Adjusting numbers, scrolling menus | | ENTER | Confirm selection | Saving changes, arming/disarming | | ARM | Initiate arming sequence | Quick arm (default mode) | | TEST | Run a sensor test | Verify each zone works | | SILENCE | Mute audible alarm | When a false alarm occurs | | LED indicators | | Quick visual status at a glance |

Problem: Alarm arms but does not lock doors.

Problem: Alarm triggers randomly.

Problem: Remote range is very short.

Problem: Siren does not chirp.

If programmed, the system will automatically lock and arm 30-60 seconds after the last door is closed and the ignition is turned off.